| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | How 3-phase induction motors work – rotating magnetic field | Animated stator/rotor interaction | | 2 | Motor nameplate: voltage, FLA, RPM, service factor, insulation class | Read 5 real nameplates | | 3 | Single-phase vs. three-phase motors | Capacitor-start motor teardown | | 4 | DC motors – series, shunt, compound | Small DC motor demo with speed control | | 5 | Motor efficiency & power factor basics | Compare efficiency labels |
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Digital multimeter (DMM) basics: V, A, Ω, continuity | Measure line voltage (120V/480V) | | 2 | Clamp meter – measuring current without breaking circuit | Measure motor FLA in a panel | | 3 | Insulation resistance tester (megohmmeter) | Test motor winding insulation | | 4 | Non-contact voltage tester & solenoid tester | Verify absence of voltage | | 5 | Understanding test lead categories (CAT III / CAT IV) | Compare meters for industrial use |
A 50 HP motor trips on overload – megger reading is 2 MΩ at 1000V. Repair or replace? Course 10: Industrial Control Panel Design & NFPA 79 Focus: Panel layout, wire bending space, grounding, and electrical standards.
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Fuse construction: fast-blow, time-delay, Class CC, J, RK5, T | Cutaway of a Class J fuse | | 2 | Circuit breaker thermal-magnetic trip mechanism | Demonstrate instantaneous vs. long-time trip | | 3 | Understanding trip curves (B, C, D, K) | Overlay trip curves on a single chart | | 4 | Selective coordination – why it matters | Two breakers in series test | | 5 | SCCR (Short-Circuit Current Rating) & fuse replacement safety | Damage from wrong fuse type |
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Megger test procedure – phase-to-phase & phase-to-ground | Acceptable values for 480V motor | | 2 | Surge comparison test for turn-to-turn shorts | Compare good vs. bad waveform | | 3 | Motor bearing types & replacement (grease vs. oil) | Pull a bearing with a puller | | 4 | Shaft alignment – dial indicator vs. laser alignment | Demonstrate soft foot | | 5 | Analyzing failed windings – overload, single-phasing, contamination | Show 5 failed stator photos |
Identify 5 code violations in a photo of a real industrial panel. Production & Delivery Notes | Element | Recommendation | |---------|----------------| | Video length per course | 45–75 minutes (broken into 5–8 segments of 5–12 min) | | Instructor | Licensed master electrician or EET with 10+ years industrial experience | | Visual style | Split-screen: instructor + live panel / motor / VFD + animated circuit diagrams | | Hands-on materials | Each course includes a downloadable worksheet, schematic, and quiz | | Certification | Completion badge + .pdf certificate per course | | Target software playback | LMS (SCORM), YouTube Unlisted, or company training portal | Optional Add‑On (11th course – Bonus) PLC & HMI for Electricians (Basics of digital inputs/outputs, ladder logic vs. relay logic, and HMI navigation for troubleshooting.)
Focus: NFPA 70E, arc flash, lockout/tagout (LOTO), and hazard recognition.
Design a conveyor start/stop with a 5-second delayed start. Course 7: Variable Frequency Drives (VFDs) – Setup & Troubleshooting Focus: VFD components, programming, motor protection, and common faults.
Identify correct PPE for a Category 2 arc flash hazard. Course 2: Multimeter & Electrical Test Equipment Focus: Proper use of DMMs, clamp meters, insulation testers, and voltage testers.
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | How 3-phase induction motors work – rotating magnetic field | Animated stator/rotor interaction | | 2 | Motor nameplate: voltage, FLA, RPM, service factor, insulation class | Read 5 real nameplates | | 3 | Single-phase vs. three-phase motors | Capacitor-start motor teardown | | 4 | DC motors – series, shunt, compound | Small DC motor demo with speed control | | 5 | Motor efficiency & power factor basics | Compare efficiency labels |
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Digital multimeter (DMM) basics: V, A, Ω, continuity | Measure line voltage (120V/480V) | | 2 | Clamp meter – measuring current without breaking circuit | Measure motor FLA in a panel | | 3 | Insulation resistance tester (megohmmeter) | Test motor winding insulation | | 4 | Non-contact voltage tester & solenoid tester | Verify absence of voltage | | 5 | Understanding test lead categories (CAT III / CAT IV) | Compare meters for industrial use |
A 50 HP motor trips on overload – megger reading is 2 MΩ at 1000V. Repair or replace? Course 10: Industrial Control Panel Design & NFPA 79 Focus: Panel layout, wire bending space, grounding, and electrical standards.
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Fuse construction: fast-blow, time-delay, Class CC, J, RK5, T | Cutaway of a Class J fuse | | 2 | Circuit breaker thermal-magnetic trip mechanism | Demonstrate instantaneous vs. long-time trip | | 3 | Understanding trip curves (B, C, D, K) | Overlay trip curves on a single chart | | 4 | Selective coordination – why it matters | Two breakers in series test | | 5 | SCCR (Short-Circuit Current Rating) & fuse replacement safety | Damage from wrong fuse type |
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Megger test procedure – phase-to-phase & phase-to-ground | Acceptable values for 480V motor | | 2 | Surge comparison test for turn-to-turn shorts | Compare good vs. bad waveform | | 3 | Motor bearing types & replacement (grease vs. oil) | Pull a bearing with a puller | | 4 | Shaft alignment – dial indicator vs. laser alignment | Demonstrate soft foot | | 5 | Analyzing failed windings – overload, single-phasing, contamination | Show 5 failed stator photos |
Identify 5 code violations in a photo of a real industrial panel. Production & Delivery Notes | Element | Recommendation | |---------|----------------| | Video length per course | 45–75 minutes (broken into 5–8 segments of 5–12 min) | | Instructor | Licensed master electrician or EET with 10+ years industrial experience | | Visual style | Split-screen: instructor + live panel / motor / VFD + animated circuit diagrams | | Hands-on materials | Each course includes a downloadable worksheet, schematic, and quiz | | Certification | Completion badge + .pdf certificate per course | | Target software playback | LMS (SCORM), YouTube Unlisted, or company training portal | Optional Add‑On (11th course – Bonus) PLC & HMI for Electricians (Basics of digital inputs/outputs, ladder logic vs. relay logic, and HMI navigation for troubleshooting.)
Focus: NFPA 70E, arc flash, lockout/tagout (LOTO), and hazard recognition.
Design a conveyor start/stop with a 5-second delayed start. Course 7: Variable Frequency Drives (VFDs) – Setup & Troubleshooting Focus: VFD components, programming, motor protection, and common faults.
Identify correct PPE for a Category 2 arc flash hazard. Course 2: Multimeter & Electrical Test Equipment Focus: Proper use of DMMs, clamp meters, insulation testers, and voltage testers.
